SEALEXCEL® Fine-Lok™/ Well-Lok™ Tube fittings have been carefully designed and manufactured with continuous research and development backing to very stringent tolerances under rigid Quality Control procedures approved to ISO 9001-2000 quality management systems to provide zero leak, Torque free seal in instrumentation and process tubing.

MATERIAL

Tube fittings are available as standard stainless steel 316. The raw materials used confirm to chemical requirements listed in specification below...

HEAT TRACEABILITY

Stainless steel 316 Tube fittings are heat code traceable back to the original mill heat from which it was made.

PRESSURE RATING

Tube fitting are rated for working pressure higher than the tubing recommended in tubing data table..

TUBING SELECTION

Stainless steel 304 and 316 fully annealed seamless tubing according to standard ASTM A213 or ASTM A269

GAS SERVICE

Extra care must be taken while selecting tubing for gas application, In order to achieve a gas-tight seal, ferrules in instruments fittings must seal any minor surface imperfections.

PIPE END NPT AND ISO
PRESSURE RATINGS

Fitting that has both tube and pipe thread ends can have different pressure ratings. The pipe end pressure ratings chart ...

Tube Fittings consist of four precision component such as Nut, Back Ferrule, Front Ferrule and Body.

CONSTRUCTION OF
FINE-LOK TUBE FITTINGS

Tube Fittings consist of three precision component such as Nut, Single Ferrule and Body.

INSTALLATION INSTRUCTION

Ensure that, the end of the tube is cut square and free from burrs without causing  undue chamfering of the tube end.

PIPE THREAD INFORMATION

Pipe fittings are available with NPT/BSP/ISO and SAE/MS straight thread.

ORDERING INFORMATION

The part Number describes completely assembled Fine-Lok / Well-Lok  Tube fittings.

CONSTRUCTION OF
WELL-LOK TUBE FITTINGS
TUBE FITTING pdf catalog
TUBE FITTING
PDF CATALOG
Download TUBE FITTING pdf catalogDownload TUBE FITTING pdf catalog
GENERAL INFORMATION
Metric Well-Lok™ Tube Fittings
Metric Well-Lok™ Tube Fittings

Construction of Fine-Lok™ Tube Fittings


Construction of Fine-Lok™ Tube FittingsConstruction of Fine-Lok™ Tube Fittings

Tube Fittings

Manufacturer of Well-Lok Tube Fittings

Precision Pipe Fittings

Precision Pipe Fittings

Ball Valves

Ball Valves

Ball Valves (High Pressure)

Ball Valves

Three Way Ball Valves

Ball Valves

Needle Valves

Ball Valves

Rising Stem Plug Valves

Ball Valves

Gauge/Root Valves

Ball Valves

Purge Valves

Ball Valves

Bleed Valves

Ball Valves

Toggle Valves

Ball Valves

Check Valves

Ball Valves

Manifold Valves

Ball Valves

Monoflange Valves

Monoflange Valves

Integral Block Bleed Valves

INTEGRAL BLOCK & BLEED VALVES

Micron In-Line Filters

Ball Valves
FEATURES & BENEFITS
Tube Fittings in SS316 are traceable
to certified material test report.

MATERIAL TRACEABILITY


Extend the fittings life by preventing
galling across a wide range of
temperature.

SILVER PLATED NUT


The leading edge of back ferrules
are case hardened.
Ensure strong Tube grip.

BACK FERRULES


Precision Machined to very close
tolerances by monitoring critical
dimensions, surface finish, run out
and sharp edges.

FRONT FERRULES


SEALEXCEL® manufacture each
and everycomponents of Tube
Fittings to very close tolerances

GAUGEABILITY


Manufactured to maximum tolerances.

PIPE THREADS


The Design of SEALEXCEL®
Well-Lok™ Twin Ferrule Tube Fittings
are similar to certain other
well-known Fittings manufacturers

INTER-CHANGEABILITY

37 Flare Tube FIttings

Tube FIttings as per DIN 2353

Precision Pipe Fittings

Quick Connect Couplings

Ball Valves

Swivel Joints

Ball Valves
HYDRAULIC
APPLICATIONS
PNEUMATIC
APPLICATIONS

SS Push in Fittings

SS Push on Fittings

Precision Pipe Fittings

Check Valves

Ball Valves

Flow Control Regulators

Ball Valves

Quick Exhaust Valves

Ball Valves

Quick Connect Couplings

Ball Valves
INSTRUMENTATION APPLICATIONS
A slight taper in the base of the tube
socket in the Fitting body.

SIZING ANGLE


Fine-Lok™ Tube Fittings consist of three precision component such as Nut, Single Ferrule and Body.
Fractional Fine-Lok™ Tube Fittings
Finger tight Fine-Lok™ Fractional Tube Fittings
Fractional Fine-Lok™ Tube Fittings
Assembled Fine-Lok™ Fractional Tube Fittings after
tightening the Nut 1-1/4 turn from the finger tight
position
Fractional Fine-Lok™ Tube Fittings
Metric Fine-Lok™ Tube Fittings
Finger tight Fine-Lok™ Metric Tube Fittings
Metric Fine-Lok™ Tube Fittings
Assembled Fine-Lok™ Metric Tube Fittings after
tightening the Nut 1-1/4 turn from the finger tight
position
Metric Fine-Lok™ Tube Fittings

Construction of Well-Lok™ Tube Fittings


Metric Well-Lok™ Tube Fittings
Finger tight Fine-Lok™ Metric Tube Fittings
Assembled Fine-Lok™ Metric Tube Fittings after
tightening the Nut 1-1/4 turn from the finger tight
position
Finger tight Fine-Lok™ Fractional Tube Fittings
Construction of Well-Lok™ Tube Fittings
Assembled Fine-Lok™ Fractional Tube Fittings after
tightening the Nut 1-1/4 turn from the finger tight
position
Fractional Well-Lok™ Tube Fittings
Fractional Well-Lok™ Tube Fittings
Well-Lok™  consist of four precision component such as Nut, Back Ferrule, Front Ferrule and Body.
 




0091-22-26788534
Sealexcel India pvt.ltd.
High Performance Fittings & Valves
Call us
Email us
sales@sealexcel.com
Home
Corporate Info
Certifications
Products
Downloads
Enquiry
Contact Us
Infrastructure
Design, R & D

Manufacturing
Quality
Testing Facilities
Packaging
Our Goal
About Us
Profile

Mission
Vision
History
Social Commitment
Network
Corporate ID No. U29120MH1993PTC070627
D & B D-U-N-S® Number: 91-842-0055
Copyright © Sealexcel India Private Limited,
All Rights Reserved - 2017
Sealexce Mobile App
Sealexcel India pvt.ltd.
Fittings and Valves
Copyright © Sealexcel India Private Limited, All Rights Reserved - 2017
Valves and Fittings
Corporate ID No. U29120MH1993PTC070627
D & B D-U-N-S® Number: 91-842-0055
Fittings and Valves
Sealexce Mobile App
Send EnquirySend Enquiry