SEALEXCEL® Fine-Lok™/ Well-Lok™ Tube fittings have been carefully designed and manufactured with continuous research and development backing to very stringent tolerances under rigid Quality Control procedures approved to ISO 9001-2000 quality management systems to provide zero leak, Torque free seal in instrumentation and process tubing.

MATERIAL

Tube fittings are available as standard stainless steel 316. The raw materials used confirm to chemical requirements listed in specification below...

HEAT TRACEABILITY

Stainless steel 316 Tube fittings are heat code traceable back to the original mill heat from which it was made.

PRESSURE RATING

Tube fitting are rated for working pressure higher than the tubing recommended in tubing data table..

TUBING SELECTION

Stainless steel 304 and 316 fully annealed seamless tubing according to standard ASTM A213 or ASTM A269

GAS SERVICE

Extra care must be taken while selecting tubing for gas application, In order to achieve a gas-tight seal, ferrules in instruments fittings must seal any minor surface imperfections.

PIPE END NPT AND ISO
PRESSURE RATINGS

Fitting that has both tube and pipe thread ends can have different pressure ratings. The pipe end pressure ratings chart ...

Tube Fittings consist of four precision component such as Nut, Back Ferrule, Front Ferrule and Body.

CONSTRUCTION OF
FINE-LOK TUBE FITTINGS

Tube Fittings consist of three precision component such as Nut, Single Ferrule and Body.

INSTALLATION INSTRUCTION

Ensure that, the end of the tube is cut square and free from burrs without causing  undue chamfering of the tube end.

PIPE THREAD INFORMATION

Pipe fittings are available with NPT/BSP/ISO and SAE/MS straight thread.

ORDERING INFORMATION

The part Number describes completely assembled Fine-Lok / Well-Lok  Tube fittings.

CONSTRUCTION OF
WELL-LOK TUBE FITTINGS
TUBE FITTING pdf catalog
TUBE FITTING
PDF CATALOG
Download TUBE FITTING pdf catalogDownload TUBE FITTING pdf catalog
GENERAL INFORMATION

Tube Fittings

Manufacturer of Well-Lok Tube Fittings

Precision Pipe Fittings

Precision Pipe Fittings

Ball Valves

Ball Valves

Ball Valves (High Pressure)

Ball Valves

Three Way Ball Valves

Ball Valves

Needle Valves

Ball Valves

Rising Stem Plug Valves

Ball Valves

Gauge/Root Valves

Ball Valves

Purge Valves

Ball Valves

Bleed Valves

Ball Valves

Toggle Valves

Ball Valves

Check Valves

Ball Valves

Manifold Valves

Ball Valves

Monoflange Valves

Monoflange Valves

Integral Block Bleed Valves

INTEGRAL BLOCK & BLEED VALVES

Micron In-Line Filters

Ball Valves
FEATURES & BENEFITS
Tube Fittings in SS316 are traceable
to certified material test report.

MATERIAL TRACEABILITY


Extend the fittings life by preventing
galling across a wide range of
temperature.

SILVER PLATED NUT


The leading edge of back ferrules
are case hardened.
Ensure strong Tube grip.

BACK FERRULES


Precision Machined to very close
tolerances by monitoring critical
dimensions, surface finish, run out
and sharp edges.

FRONT FERRULES


SEALEXCEL® manufacture each
and everycomponents of Tube
Fittings to very close tolerances

GAUGEABILITY


Manufactured to maximum tolerances.

PIPE THREADS


The Design of SEALEXCEL®
Well-Lok™ Twin Ferrule Tube Fittings
are similar to certain other
well-known Fittings manufacturers

INTER-CHANGEABILITY

37 Flare Tube FIttings

Tube FIttings as per DIN 2353

Precision Pipe Fittings

Quick Connect Couplings

Ball Valves

Swivel Joints

Ball Valves
HYDRAULIC
APPLICATIONS
PNEUMATIC
APPLICATIONS

SS Push in Fittings

SS Push on Fittings

Precision Pipe Fittings

Check Valves

Ball Valves

Flow Control Regulators

Ball Valves

Quick Exhaust Valves

Ball Valves

Quick Connect Couplings

Ball Valves
INSTRUMENTATION APPLICATIONS
A slight taper in the base of the tube
socket in the Fitting body.

SIZING ANGLE


Male Pipe Weld Connector

Instrument Fittings Manufacturers


Instrument Fittings ManufacturersInstrument Fittings Manufacturers
Instrument Fittings ManufacturersInstrument Fittings Manufacturers
Dimensions are for reference only and are subject to change without Notice

TUBE

OD

MALE

PIPE

WELD

DIMENSIONS IN MM

PART NO.

T

SIZE

B

E

F

G

L

J

Well-Lok

Fine-Lok

3

1/8

9.7

2.4

11.0

11.0

23.9

10.3

MWC-3-125

SMWC-3-125

4

1/8

9.7

2.4

12.0

12.0

24.6

10.3

MWC-4-125

SMWC-4-125

6

1/8

9.7

4.8

14.0

14.0

25.4

10.3

MWC-6-125

SMWC-6-125

6

1/4

14.2

4.8

14.0

14.0

30.5

13.7

MWC-6-250

SMWC-6-250

8

1/8

9.7

5.1

16.0

16.0

26.7

10.3

MWC-8-125

SMWC-8-125

8

1/4

14.2

6.4

16.0

16.0

31.2

13.7

MWC-8-250

SMWC-8-250

8

1/2

19.0

6.4

22.0

16.0

38.1

21.3

MWC-8-500

SMWC-8-500

10

1/4

14.2

7.1

18.0

19.0

33.3

13.7

MWC-10-250

SMWC-10-250

10

3/8

14.2

7.9

18.0

19.0

33.3

17.1

MWC-10-375

SMWC-10-375

10

1/2

19.0

7.9

22.0

19.0

38.9

21.3

MWC-10-500

SMWC-10-500

12

1/4

14.2

7.1

22.0

22.0

33.3

13.7

MWC-12-250

SMWC-12-250

12

3/8

14.2

9.5

22.0

22.0

33.3

17.1

MWC-12-375

SMWC-12-375

12

1/2

19.0

9.5

22.0

22.0

38.9

21.3

MWC-12-500

SMWC-12-500

14

3/8

14.2

10.3

24.0

25.0

34.0

17.1

MWC-14-375

SMWC-14-375

15

1/2

19.0

11.9

24.0

25.0

38.9

21.3

MWC-15-500

SMWC-15-500

16

1/2

19.0

12.7

24.0

25.0

38.9

21.3

MWC-16-500

SMWC-16-500

18

1/2

19.0

13.5

27.0

30.0

40.4

21.3

MWC-18-500

SMWC-18-500

 

 

 

 

Male Pipe Weld Connector
For metric Tube to male pipe weld connection

 

Male Pipe Weld Elbow

Dimensions are for reference only and are subject to change without Notice

TUBE

OD

MALE

PIPE WELD

DIMENSIONS IN INCH

PART NO.

T

SIZE

B

E

F

G

Lx

Ly

J

Well-Lok

Fine-Lok

1/4

1/8

0.38

0.19

1/2

9/16

0.77

0.74

0.405

MWE-250-125

SMWE-250-125

1/4

1/4

0.56

0.19

1/2

9/16

0.77

0.92

0.540

MWE-250-250

SMWE-250-250

3/8

1/4

0.56

0.28

5/8

11/16

0.91

1.00

0.540

MWE-375-250

SMWE-375-250

1/2

1/2

0.75

0.41

13/16

7/8

1.02

1.30

0.840

MWE-500-500

SMWE-500-500

3/4

3/4

0.75

0.62

1-1/16

1-1/8

1.17

1.45

1.050

MWE-750-750

SMWE-750-750

 

 

 

 

Male Pipe Weld Elbow
For Fractional Tube to male pipe weld  connection
 

Reducer

Dimensions are for reference only and are subject to change without Notice

TUBE

OD

TUBE

OD

DIMENSIONS IN INCH

PART NO.

T

Tx

E

F

G

L

Well-Lok

Fine-Lok

1/8

1/8

0.08

7/16

7/16

1.06

R-125-125

SR-125-125

1/8

3/16

0.09

7/16

7/16

1.09

R-125-187

SR-125-187

1/8

1/4

0.09

7/16

7/16

1.16

R-125-250

SR-125-250

1/8

3/8

0.09

7/16

7/16

1.22

R-125-375

SR-125-375

1/8

1/2

0.09

9/16

7/16

1.48

R-125-500

SR-125-500

3/16

1/8

0.08

7/16

1/2

1.11

R-187-125

SR-187-125

3/16

1/4

0.12

7/16

1/2

1.20

R-187-250

SR-187-250

1/4

1/8

0.08

1/2

9/16

1.16

R-250-125

SR-250-125

1/4

3/16

0.12

1/2

9/16

1.19

R-250-187

SR-250-187

1/4

1/4

0.19

1/2

9/16

1.25

R-250-250

SR-250-250

1/4

5/16

0.19

1/2

9/16

1.28

R-250-312

SR-250-312

1/4

3/8

0.19

1/2

9/16

1.31

R-250-375

SR-250-375

1/4

1/2

0.19

9/16

9/16

1.53

R-250-500

SR-250-500

1/4

5/8

0.19

11/16

9/16

1.60

R-250-625

SR-250-625

1/4

3/4

0.19

13/16

9/16

1.59

R-250-750

SR-250-750

5/16

3/8

0.25

9/16

5/8

1.36

R-312-375

SR-312-375

5/16

1/2

0.25

9/16

5/8

1.58

R-312-500

SR-312-500

3/8

1/4

0.19

5/8

11/16

1.34

R-375-250

SR-375-250

3/8

3/8

0.28

5/8

11/16

1.41

R-375-375

SR-375-375

3/8

1/2

0.28

5/8

11/16

1.62

R-375-500

SR-375-500

3/8

5/8

0.28

11/16

11/16

1.69

R-375-625

SR-375-625

3/8

3/4

0.28

13/16

11/16

1.69

R-375-750

SR-375-750

1/2

1/4

0.19

13/16

7/8

1.37

R-500-250

SR-500-250

1/2

3/8

0.28

13/16

7/8

1.44

R-500-375

SR-500-375

1/2

1/2

0.39

13/16

7/8

1.66

R-500-500

SR-500-500

1/2

5/8

0.41

13/16

7/8

1.72

R-500-625

SR-500-625

1/2

3/4

0.41

13/16

7/8

1.72

R-500-750

SR-500-750

1/2

1

0.41

1-1/16

7/8

1.97

R-500-1000

SR-500-1000

5/8

3/4

0.50

15/16

1

1.75

R-625-750

SR-625-750

5/8

7/8

0.50

15/16

1

1.81

R-625-875

SR-625-875

5/8

1

0.50

1-1/16

1

2.00

R-625-1000

SR-625-1000

3/4

1/2

0.39

1-1/16

1-1/8

1.75

R-750-500

SR-750-500

3/4

1

0.62

1-1/16

1-1/8

2.06

R-750-1000

SR-750-1000

 

 

 

Reducer
For Fractional Tube to fractional ports connection
Male Pipe Weld ConnectorMale Pipe Weld Connector
Male Pipe Weld ElbowMale Pipe Weld Elbow
ReducerReducer
Instrument Fittings ManufacturersInstrument Fittings Manufacturers

TUBE

OD

MALE

PIPE

WELD

SEALEXCEL PART NO.

T

SIZE

Well-Lok

Fine-Lok

Twin Ferrule Tube Fittings

Single Ferrule Tube Fittings

3

1/8

MWC-3-125

SMWC-3-125

4

1/8

MWC-4-125

SMWC-4-125

6

1/8

MWC-6-125

SMWC-6-125

6

1/4

MWC-6-250

SMWC-6-250

8

1/8

MWC-8-125

SMWC-8-125

8

1/4

MWC-8-250

SMWC-8-250

8

1/2

MWC-8-500

SMWC-8-500

10

1/4

MWC-10-250

SMWC-10-250

10

3/8

MWC-10-375

SMWC-10-375

10

1/2

MWC-10-500

SMWC-10-500

12

1/4

MWC-12-250

SMWC-12-250

12

3/8

MWC-12-375

SMWC-12-375

12

1/2

MWC-12-500

SMWC-12-500

14

3/8

MWC-14-375

SMWC-14-375

15

1/2

MWC-15-500

SMWC-15-500

16

1/2

MWC-16-500

SMWC-16-500

18

1/2

MWC-18-500

SMWC-18-500