Bite-Lok Tube Fittings catalog download
SEALEXCEL® Bite-Lok® Flareless 
Bite Type Tube Fittings are
designed according to DIN 2353
and manufactured under rigid
quality control procedure approved
to ISO 9001:2008 and tested
according to extensive testing
procedure BS4368 part IV
Bite-Lok Tube Fittings
Bite-Lok Tube Fittings
HEAT TRACEABILITY
SEALEXCEL® Bite-Lok® stainless
steel Tube Fittings are heat code
traceable back to the original mill
heat from which it was made.

PRESSURE RATING
BUNA-N :-35º C to 100º C
FPM (VITON)®: -25º C to 200º C

MATERIAL
Available as standard in material  stainless steel.

Bite-Lok Tube Fittings catalog
BITE-LOK
TUBE FITTINGS
PDF CATALOG
Bite-Lok Tube Fittings catalog downloadBite-Lok Tube Fittings catalog download
GENERAL INFORMATION
SEALEXCEL® Bite-Lok® Tube Fittings
are suitable for use at the following
nominal pressure.
Stainless Steel : up to 400ºC
Caution : For higher temperatures,
reduction in pressures should be
taken in to account

TEMPERATURE RATING

FOR SEAL MATERIAL
STUDS AND PORT FORMS
Metric ISO Thread : DIN 3852, Part 1
BSP Thread            : DIN 3852, Part 2

TIGHTENING TORQUES FOR STUDS
Metric ISO Thread : DIN 3852, Part 1
BSP Thread            : DIN 3852, Part 2

INSTALLATION INSTRUCTIONS
Assembly In Hardened
Pre-Assembly Body.
general information
general information
GENERAL INFORMATION
pneumatic applications
PNEUMATIC
APPLICATIONS
hydraulic applications
HYDRAULIC
APPLICATIONS
Instrumentation applications
INSTRUMENTATION APPLICATIONS
DESIGN
SEALEXCEL has designed the Bite
Ring very carefully with proper
consideration having twin Biting
edges to have firm and safe gripping
on tubing to provide leak free
connection of tube and components
in fluid systems.
FUNCTION
As the Bite-Lok® Tube Fittings Nut
tightened, the Bite Ring moves
towards the surface of the tube and
the front Biting edge 'A' of the Bite
Ring starts Biting tube

TUBING SELECTION
We recommend stainless steel cold
drawn fully annealed seamless
tubing to DIN 17458 or equivalent
and provide tolerances to DIN 2391
part 1


37 Flare Tube FIttings

Tube FIttings as per DIN 2353

Precision Pipe Fittings

Quick Connect Couplings

Ball Valves

Swivel Joints

Ball Valves

SS Push in Fittings

SS Push on Fittings

Push on Fittings

Check Valves

Ball Valves

Flow Control Regulators

Ball Valves

Quick Exhaust Valves

Ball Valves

Quick Connect Couplings

Ball Valves

Tube Fittings

Manufacturer of Well-Lok Tube Fittings

Precision Pipe Fittings

Precision Pipe Fittings

Ball Valves

Ball Valves

Ball Valves (High Pressure)

Ball Valves

Three Way Ball Valves

Ball Valves

Needle Valves

Ball Valves

Rising Stem Plug Valves

Ball Valves

Gauge/Root Valves

Ball Valves

Purge Valves

Ball Valves

Bleed Valves

Ball Valves

Toggle Valves

Ball Valves

Check Valves

Ball Valves

Manifold Valves

Ball Valves

Monoflange Valves

Monoflange Valves

Integral Block Bleed Valves

INTEGRAL BLOCK & BLEED VALVES

Micron In-Line Filters

Ball Valves
Bite-Lok Tube Fittings As per DIN 2353

INSTALLATION INSTRUCTIONS
ASSEMBLY IN HARDENED PRE-ASSEMBLY BODY.
INSTALLATION INSTRUCTIONS
In order to ensure positive
assembly, SEALEXCEL recommend pre-assembled the tube and fittings in hardened pre-assembly Body.
ASSEMBLY IN HARDENED PRE-ASSEMBLY BODY
Ensure that the end of Tube is cut square within + 1/2º angle to the tube axis.
Remove  the burs and sharp edges to the maximum chamfer 0.2 mm x 45º at both inside and outside edge of the tube.
1)
2)
ASSEMBLY IN HARDENED PRE-ASSEMBLY BODY
Lubricate the thread and cone of the pre-assembly body, Bite Ring and thread of the nut.
3)

Insert the Nut and Bite Ring
Insert the Nut and Bite Ring
over tube end.
Screw on Nut manually
Screw on Nut manually on to
pre-assembly body until finger tight, hold tube against the shoulder in the cone of
pre-assembly body
4)
5)
Tighten the Nut with wrench
Tighten the Nut with wrench 1 turn from the finger tight position.
6)

Loosen the Nut
Loosen the Nut, remove the tube from the pre-assembly body, check the  penetration of cutting edge. A visible collar fills space in front of first cutting  edge completely. It does not matter even Bite Ring rotate on tube end.
Final assembly in Fitting body
Final assembly in Fitting body Put pre-installed tube in to the fitting body.
Tighten the Nut with wrench by
approx 1/2 turns beyond point of clearly perceptible resistance.
7)
8)
Repeated Assembly
Repeated Assembly
9)
Each time the fitting is disassembled, the nut must be re-tightened firmly using the same torque as required for final assembly
Sealexcel India pvt.ltd.
High Performance Fittings & Valves
Call us
Email us
0091-22-26788534
sales@sealexcel.com
Home
Corporate Info
Certifications
Products
Downloads
Enquiry
Contact Us
Infrastructure
Design, R & D

Manufacturing
Quality
Testing Facilities
Packaging
Our Goal
About Us
Profile

Mission
Vision
History
Social Commitment
Network
Corporate ID No. U29120MH1993PTC070627
D & B D-U-N-S® Number: 91-842-0055
Copyright © Sealexcel India Private Limited,
All Rights Reserved - 2017
Sealexce Mobile App
Bite-Lok Tube Fittings
Bite-Lok Tube Fittings
As per DIN 2353
Pressure Rating : Up to 250 bar
Temperature Rating : Up to 400º C
Bite-Lok Tube Fittings
Copyright © Sealexcel India Private Limited, All Rights Reserved - 2017
Bite-Lok Tube Fittings
Corporate ID No. U29120MH1993PTC070627
D & B D-U-N-S® Number: 91-842-0055
Bite-Lok Tube Fittings
Sealexce Mobile App
Send EnquirySend Enquiry