SEALEXCEL® Fine-Lok™/ Well-Lok™ Tube fittings have been carefully designed and manufactured with continuous research and development backing to very stringent tolerances under rigid Quality Control procedures approved to ISO 9001-2000 quality management systems to provide zero leak, Torque free seal in instrumentation and process tubing.

MATERIAL

Tube fittings are available as standard stainless steel 316. The raw materials used confirm to chemical requirements listed in specification below...

HEAT TRACEABILITY

Stainless steel 316 Tube fittings are heat code traceable back to the original mill heat from which it was made.

PRESSURE RATING

Tube fitting are rated for working pressure higher than the tubing recommended in tubing data table..

TUBING SELECTION

Stainless steel 304 and 316 fully annealed seamless tubing according to standard ASTM A213 or ASTM A269

GAS SERVICE

Extra care must be taken while selecting tubing for gas application, In order to achieve a gas-tight seal, ferrules in instruments fittings must seal any minor surface imperfections.

PIPE END NPT AND ISO
PRESSURE RATINGS

Fitting that has both tube and pipe thread ends can have different pressure ratings. The pipe end pressure ratings chart ...

Tube Fittings consist of four precision component such as Nut, Back Ferrule, Front Ferrule and Body.

CONSTRUCTION OF
FINE-LOK TUBE FITTINGS

Tube Fittings consist of three precision component such as Nut, Single Ferrule and Body.

INSTALLATION INSTRUCTION

Ensure that, the end of the tube is cut square and free from burrs without causing  undue chamfering of the tube end.

PIPE THREAD INFORMATION

Pipe fittings are available with NPT/BSP/ISO and SAE/MS straight thread.

ORDERING INFORMATION

The part Number describes completely assembled Fine-Lok / Well-Lok  Tube fittings.

CONSTRUCTION OF
WELL-LOK TUBE FITTINGS
TUBE FITTING pdf catalog
TUBE FITTING
PDF CATALOG
Download TUBE FITTING pdf catalogDownload TUBE FITTING pdf catalog
GENERAL INFORMATION
Male Connector (EO-Seal ISO Parallel Thread)
Male Connector (EO-Seal ISO Parallel Thread)

TUBE

OD

BSPP MALE THREAD

DIMENSIONS IN MM

PART NO.

T

P

B

E

F

Fd

G

L

Well-Lok

Fine-Lok

3

1/8

7.1

2.4

14.0

13.8

11.0

23.4

MC-3-125RP

SMC-3-125RP

3

1/4

11.2

2.4

19.0

18.0

11.0

28.7

MC-3-250RP

SMC-3-250RP

4

1/8

7.1

2.4

14.0

13.8

12.0

24.1

MC-4-125RP

SMC-4-125RP

6

1/8

7.1

4.0

14.0

13.8

14.0

24.9

MC-6-125RP

SMC-6-125RP

6

1/4

11.2

4.8

19.0

18.0

14.0

30.2

MC-6-250RP

SMC-6-250RP

6

3/8

11.2

4.8

22.0

21.8

14.0

31.5

MC-6-375RP

SMC-6-375RP

6

1/2

14.2

4.8

27.0

26.0

14.0

37.3

MC-6-500RP

SMC-6-500RP

8

1/8

7.1

4.0

16.0

13.8

16.0

25.7

MC-8-125RP

SMC-8-125RP

8

1/4

11.2

6.4

19.0

18.0

16.0

31.0

MC-8-250RP

SMC-8-250RP

8

3/8

11.2

6.4

22.0

21.8

16.0

32.3

MC-8-375RP

SMC-8-375RP

8

1/2

14.2

6.4

27.0

26.0

16.0

38.1

MC-8-500RP

SMC-8-500RP

10

1/4

11.2

5.9

19.0

18.0

19.0

31.8

MC-10-250RP

SMC-10-250RP

10

3/8

11.2

7.9

22.0

21.8

19.0

33.0

MC-10-375RP

SMC-10-375RP

10

1/2

14.2

7.9

27.0

26.0

19.0

38.9

MC-10-500RP

SMC-10-500RP

12

1/4

11.2

5.9

22.0

18.0

22.0

32.5

MC-12-250RP

SMC-12-250RP

12

3/8

11.2

7.9

22.0

21.8

22.0

33.0

MC-12-375RP

SMC-12-375RP

12

1/2

14.2

9.5

27.0

26.0

22.0

38.9

MC-12-500RP

SMC-12-500RP

12

3/4

15.7

9.5

35.0

32.0

22.0

42.7

MC-12-750RP

SMC-12-750RP

15

1/2

14.2

11.9

27.0

26.0

25.0

38.9

MC-15-500RP

SMC-15-500RP

16

3/8

11.2

7.9

24.0

21.8

25.0

33.8

MC-16-375RP

SMC-16-375RP

16

1/2

14.2

11.9

27.0

26.0

25.0

38.9

MC-16-500RP

SMC-16-500RP

18

1/2

14.2

11.9

27.0

26.0

30.0

38.9

MC-18-500RP

SMC-18-500RP

18

3/4

15.7

15.1

35.0

32.0

30.0

42.7

MC-18-750RP

SMC-18-750RP

20

1/2

14.2

11.9

30.0

26.0

32.0

40.4

MC-20-500RP

SMC-20-500RP

20

3/4

15.7

15.9

35.0

32.0

32.0

42.7

MC-20-750RP

SMC-20-750RP

22

3/4

15.7

15.9

35.0

32.0

32.0

42.7

MC-22-750RP

SMC-22-750RP

22

1

18.3

18.3

41.0

39.0

32.0

45.2

MC-22-1000RP

SMC-22-1000RP

25

3/4

15.7

15.9

35.0

32.0

38.0

45.2

MC-25-750RP

SMC-25-750RP

25

1

18.3

19.8

41.0

39.0

38.0

47.8

MC-25-1000RP

SMC-25-1000RP

 

 

 

Male Connector (EO-Seal ISO Parallel Thread)

Metric Compression Tube Fittings


For Fractional Tube To Female ISO Parallel Pipe Thread Connection

Tube Fittings EnquiryTube Fittings Enquiry

Male Connector (EO-Seal ISO Parallel Thread)

For Metric Tube To Female ISO Parallel Pipe Thread Connection


 

Tube Fittings

Manufacturer of Well-Lok Tube Fittings

Precision Pipe Fittings

Precision Pipe Fittings

Ball Valves

Ball Valves

Ball Valves (High Pressure)

Ball Valves

Three Way Ball Valves

Ball Valves

Needle Valves

Ball Valves

Rising Stem Plug Valves

Ball Valves

Gauge/Root Valves

Ball Valves

Purge Valves

Ball Valves

Bleed Valves

Ball Valves

Toggle Valves

Ball Valves

Check Valves

Ball Valves

Manifold Valves

Ball Valves

Monoflange Valves

Monoflange Valves

Integral Block Bleed Valves

INTEGRAL BLOCK & BLEED VALVES

Micron In-Line Filters

Ball Valves
FEATURES & BENEFITS
Tube Fittings in SS316 are traceable
to certified material test report.

MATERIAL TRACEABILITY


Extend the fittings life by preventing
galling across a wide range of
temperature.

SILVER PLATED NUT


The leading edge of back ferrules
are case hardened.
Ensure strong Tube grip.

BACK FERRULES


Precision Machined to very close
tolerances by monitoring critical
dimensions, surface finish, run out
and sharp edges.

FRONT FERRULES


SEALEXCEL® manufacture each
and everycomponents of Tube
Fittings to very close tolerances

GAUGEABILITY


Manufactured to maximum tolerances.

PIPE THREADS


The Design of SEALEXCEL®
Well-Lok™ Twin Ferrule Tube Fittings
are similar to certain other
well-known Fittings manufacturers

INTER-CHANGEABILITY

37 Flare Tube FIttings

Tube FIttings as per DIN 2353

Precision Pipe Fittings

Quick Connect Couplings

Ball Valves

Swivel Joints

Ball Valves
HYDRAULIC
APPLICATIONS
PNEUMATIC
APPLICATIONS

SS Push in Fittings

SS Push on Fittings

Precision Pipe Fittings

Check Valves

Ball Valves

Flow Control Regulators

Ball Valves

Quick Exhaust Valves

Ball Valves

Quick Connect Couplings

Ball Valves
INSTRUMENTATION APPLICATIONS
A slight taper in the base of the tube
socket in the Fitting body.

SIZING ANGLE


TUBE

OD

BSPP

MALE

THREAD

DIMENSIONS IN INCH

PART NO.

T

P

B

E

F

Fd

G

L

Well-Lok

Fine-Lok

1/4

1/4

0.47

0.19

3/4

0.74

9/16

1.19

OMC-250-250EO

SOMC-250-250EO

1/4

1/2

0.55

0.19

1-1/16

1.04

9/16

1.38

OMC-250-500EO

SOMC-250-500EO

3/8

3/8

0.47

0.28

7/8

0.86

11/16

1.31

OMC-375-375EO

SOMC-375-375EO

1/2

1/4

0.47

0.25

13/16

0.74

7/8

1.31

OMC-500-250EO

SOMC-500-250EO

1/2

3/8

0.47

0.31

7/8

0.86

7/8

1.31

OMC-500-375EO

SOMC-500-375EO

1/2

1/2

0.55

0.41

1-1/16

1.04

7/8

1.47

OMC-500-500EO

SOMC-500-500EO

3/4

3/4

0.63

0.63

1-5/16

1.25

1-1/8

1.59

OMC-750-750EO

SOMC-750-750EO

 

 

TUBE

OD

BSPP MALE THREAD

DIMENSIONS IN MM

PART NO.

T

P

B

E

F

Fd

G

L

Well-Lok

Fine-Lok

6

1/8

7.9

4.0

14.0

13.7

14.0

25.0

OMC-6-125EO

SOMC-6-125EO

6

1/4

11.9

4.8

19.0

18.8

14.0

30.7

OMC-6-250EO

SOMC-6-250EO

6

3/8

11.9

4.8

22.0

21.8

14.0

32.0

OMC-6-375EO

SOMC-6-375EO

6

1/2

14.0

4.8

27.0

26.4

14.0

37.0

OMC-6-500EO

SOMC-6-500EO

10

1/4

11.9

5.9

19.0

18.8

19.0

32.3

OMC-10-250EO

SOMC-10-250EO

10

3/8

11.9

7.9

22.0

21.8

19.0

38.1

OMC-10-375EO

SOMC-10-375EO

10

1/2

14.0

7.9

27.0

26.4

19.0

38.4

OMC-10-500EO

SOMC-10-500EO

12

1/4

11.9

5.9

22.0

18.8

22.0

33.0

OMC-12-250EO

SOMC-12-250EO

12

3/8

11.9

7.9

22.0

21.8

22.0

33.5

OMC-12-375EO

SOMC-12-375EO

12

1/2

14.0

9.5

27.0

26.4

22.0

38.4

OMC-12-500EO

SOMC-12-500EO

 

Dimensions are for reference only and are subject to change without Notice
Dimensions are for reference only and are subject to change without Notice

TUBE

OD

BSPP MALE THREAD

DIMENSIONS IN INCH

PART NO.

T

P

B

E

F

Fd

G

L

Well-Lok

Fine-Lok

1/8

1/8

0.28

0.09

9/16

0.54

7/16

0.92

MC-125-125RP

SMC-125-125RP

1/8

1/4

0.44

0.09

3/4

0.71

7/16

1.13

MC-125-250RP

SMC-125-250RP

1/4

1/8

0.28

0.19

9/16

0.54

9/16

0.98

MC-250-125RP

SMC-250-125RP

1/4

1/4

0.44

0.19

3/4

0.71

9/16

1.19

MC-250-250RP

SMC-250-250RP

1/2

1/2

0.56

0.41

1-1/16

1.02

7/8

1.53

MC-500-500RP

SMC-500-500RP

 

 

 

Dimensions are for reference only and are subject to change without Notice
Male Connector (ISO Parallel Thread-RP)

Male Connector (ISO Parallel Thread-RP)

For fractional Tube to Female ISO Parallel pipe thread connection

 
Tube Fittings EnquiryTube Fittings Enquiry
Dimensions are for reference only and are subject to change without Notice
Male Connector (ISO Parallel Thread-RP)

For Metric tube to Female ISO Parallel pipe thread connection

Male Connector (ISO Parallel Thread-RP)


 
Tube Fittings IndexTube Fittings Index
Tube Fittings next pageTube Fittings next page
Tube Fittings InquiryTube Fittings Inquiry

TUBE

OD

BSPP

MALE

THREAD

SEALEXCEL PART NO.

T

P

Well-Lok

Fine-Lok

Twin Ferrule Tube Fittings

Single Ferrule Tube Fittings

1/4

1/4